0

Electrical Connectors

Missing the right connector for a sensor, a fuel injector or a new wiring harness? Here we bring together connector housings, pins, terminals and cable lugs for you who repair, modify or build a new electrical system in your project.

Connectors, housings and terminals in the wiring harness

A connector typically consists of a connector housing, metal terminals and often seals as well as a secondary lock that holds the terminals in place. In this category you will find, for example, connector housings in systems such as Molex MX-150, AMP Multilock, Delphi and Superseal from NAMZ and Haltech, short pigtails with pre-fitted connectors and battery cable lugs from Moroso.

How to choose the right connector

  • Connector system: The housing and terminals must belong to the same system. Terminals from one system typically do not fit another.
  • Pin count and layout: Check the number of positions, rows and keying, and whether you need a male or female part.
  • Wire gauge: The terminal must match the wire's cross-section and insulation. For battery cables, the choice depends on cable size and stud diameter.
  • Sealing: In the engine bay, sealed connectors can help protect against moisture and dirt.
  • OEM number: Several connectors are listed with the original part number, so you can compare with the connector you are replacing.

Installation and durability

Terminals are typically crimped with a tool that matches that specific terminal type. A poor crimp can cause loose connections and voltage drop. If you need new wire, you will find it under wire and cable, while wire loom can shield the joint from wear and heat. For larger conversions, complete wiring harnesses can be an alternative.

Frequently asked questions

Can I reuse the old terminals in a new connector housing?

It depends on the connector system. The terminals must fit that specific housing, and used terminals can be deformed or corroded. It is often safest to use new terminals and seals, especially in the engine bay.

What is a secondary lock on a connector?

It is an extra locking part in the connector housing that holds the terminals in place when the connector is assembled. It can reduce the risk of a terminal backing out due to vibration. Not all connectors have a secondary lock.

Should I crimp or solder cable lugs?

It depends on the terminal and your tools. Some cable lugs, such as the Moroso battery cable kit, can be both crimped and soldered. Whatever the method, the joint should be made correctly and strain-relieved so vibrations do not stress the connection.

View as Grid List
Sort by
Display per page

Fleece Performance Wiring Hrnss Cnnctr

fpeFPE-HAR-MU-PT-7
Fleece Performance Universal MAP Sensor & Airbox Control Valve Pigtail
49,46 € excl. VAT

Fleece Performance Wiring Hrnss Cnnctr

fpeFPE-HAR-GM-NSBU-0104
Fleece Performance 01-04 GM 2500/3500 Duramax (w/Allison Transmission) NSBU Pigtails
116,74 € excl. VAT

Fleece Performance Wiring Hrnss Cnnctr

fpeFPE-HAR-DMAX-LB7-INJ-PT
Fleece Performance 01-04 GM 2500/3500 Duramax LB7 Outer Injector Connector Pigtail
50,82 € excl. VAT

Fleece Performance Wiring Hrnss Cnnctr

fpeFPE-HAR-CUMM-FH-PT
Fleece Performance 00-18 Dodge 2500/3500Cummins 5.9L/6.7L Fuel Heater Connector & 6in Pigtail
34,53 € excl. VAT

Granatelli Coil Connector

gms28-8051HTB
Granatelli 20-23 GM LT2 6.2L Hi-Perf Coil-Near-Plug Ignition Wire Connector Kit w/Black Jacket
230,68 € excl. VAT