0

Manifold Flanges

Building your own headers, or need to replace a damaged flange on an exhaust manifold? Manifold flanges are the plates the tubes are welded to, connecting them to the cylinder head or the next part of the exhaust. They are for you if you fabricate or repair exhaust systems as part of a project.

What does a manifold flange do?

The flange must provide a flat, tight seal between the tubes and the cylinder head or between two sections of the exhaust. Here you will find both cylinder head flanges for headers – manifolds with separate tubes for each cylinder – and universal 2-bolt 2-1/2 inch flanges for joints further down the system. If you need a ready-made solution, take a look at our exhaust manifolds or the full category of manifolds.

How to choose the right flange

  • Engine and ports: The flange must match the exhaust ports of the cylinder head, e.g. SBC with 18° or 23° angle, Small Block Ford, GM LS, LT-1 or 5.7 Hemi with square ports. Some flanges are side-specific.
  • Tube diameter: The holes fit a specific tube size, e.g. 1 7/8 or 2 1/8 inch. The right choice depends on the tubes, the engine and your power goal.
  • Bank or individual flanges: A one-piece flange for the whole cylinder bank keeps the port spacing fixed, while individual flanges give more freedom when fitting.
  • Material: Stainless steel or mild steel – typically choose the same material as the tubes so the weld is consistent.

Installation and welding

A flange can warp from the heat during welding, so it is a good idea to bolt it to a cylinder head or a fixture while welding and check flatness afterwards. At Kooks Headers you will find, for example, flanges for SBC, SB Ford and GM LS in both stainless steel and mild steel. Whether a modified exhaust can be approved for road use depends on the car and the overall setup and must be checked in each specific case.

Frequently asked questions

What is the difference between a bank flange and individual flanges?

A bank flange is one piece for the whole cylinder bank and keeps the ports at the correct spacing relative to each other. Individual flanges are one per port and can give more room to adjust the tube routing, but require more care when clamping up.

What do 18° and 23° mean for SBC flanges?

The angle typically refers to the valve angle in the cylinder head, which affects the position and shape of the ports. The flange must match your exact cylinder head, so check the specifications of both cylinder head and flange before you choose.

Why does the joint leak after welding?

The heat from welding can cause the flange to warp so it no longer sits flat against the cylinder head. This can typically be remedied by surfacing the flange flat, using a suitable gasket and retightening the bolts after the first heat cycles.

View as Grid List
Sort by
Display per page

Small Block Ford Header Flange

ksh7011-SH-B
Kooks SB Ford 1 7/8in Steel Street Heat Flange (Bank)
51,44 € excl. VAT

Small Block Ford Header Flange

ksh7022-S-0410
Kooks SB Ford 2in SS TWR / VJR / Street Heat Flange (Individual)
90,87 € excl. VAT

Small Block Ford Header Flange

ksh7011-SH-A
Kooks SB Ford 2in Steel Street Heat Flange (Bank)
66,22 € excl. VAT

Small Block Ford Header Flange

ksh7011-S
Kooks SB Ford 2in SS Ford Outer Flange (Bank)
107,98 € excl. VAT

Small Block Ford Header Flange

ksh7051-S
Kooks SB Ford 1 7/8in SS Canfield/Dart Flange (Bank)
98,38 € excl. VAT

Small Block Ford Header Flange

ksh7011-D
Kooks SB Ford 1 7/8 Steel Ford Outer Flange (Bank)
70,59 € excl. VAT